Logo1
Logo2 home forum Snowmobiles atvs
TopCorner PageBorder

Welcome Guest ( Log In | Register )

 
 Reply to this topicStart new topic
> FST/FS Service Manual
sask prairie
post Feb 25 2011, 11:41 PM
Post #1


Junior Member
**

Group: Members
Posts: 115
Joined: 10-February 09
From: Saskatoon Canada
Member No.: 3,809
Current Vehicle:
2006 FST Classic
Age: 42
OK installed new motor after lod one rod bearing went. If anyone read yayou's article on oil pump replacement I think is a good idea. So have code p0107 which is mass fuel sensor at boost box. Changed it and still can't clear codes. But sinse then the p0234 and 90238 codes come up and can not clear. All wiring seams OK any suggestions?
Go to the top of the page
 
+Quote Post
Sponsor


Juiced
post Feb 26 2011, 02:19 PM
Post #2


Average Member
***

Group: Members
Posts: 729
Joined: 15-December 07
From: CT
Member No.: 1,863
Current Vehicle:
07 FST IQ
Age: 35
Maybe the infamous violet wire.....


--------------------
Started as an 07 FST IQ

Garrett GT2056 Turbo
Precision Sports GT25R Flash
Precision Sports Clutching
Stainless tubular watercooled Exhaust Manifold
3" Exhaust right out of the Turbo
Racecraft-Fabrication 3" "Stock" Muffler
Racecraft-Fabrication Intercooler
Racecraft-Fabrication Aluminum Boost Box
TurboXS BOV
TurboSmart E-Boost 2-Boost Controller (21.5psi)
Watercraft Charging system
Water/Methanol Injection
23-44 Gears
136" Camoplast Cobra Track
216 Woodys Chisels
8" rear wheels with Avid offset axle
Data Logger w/ Innovate Wideband
2 Step Launch Control

It's basically stock!
Go to the top of the page
 
+Quote Post
sask prairie
post Feb 27 2011, 05:50 PM
Post #3


Junior Member
**

Group: Members
Posts: 115
Joined: 10-February 09
From: Saskatoon Canada
Member No.: 3,809
Current Vehicle:
2006 FST Classic
Age: 42
Ok, grounded the violet wire out to the ecu peg. Left the violet wire going into the ecu not grounded. Have 5 volts going to the yellow black and 5 volts going to the red at the sensor as well. somewhere i read you should only have over 1 volts going to the red wire? Checked continuity at the purple wire and have continuity. Still have all 4 codes. Have changed the sensor but still no luck. Could it be the ecu and why did it fail when rod bearing went? Stumped. I now have p1553 code to as well. I think it due to a ground issue. could i have missed a ground somewhere when putting engine back into sled.

This post has been edited by sask prairie: Feb 27 2011, 05:55 PM
Go to the top of the page
 
+Quote Post
1RMDave
post Feb 27 2011, 06:22 PM
Post #4


Average Member
***

Group: Admin
Posts: 868
Joined: 14-March 08
From: Manitoba
Member No.: 2,471
Current Vehicle:
07 RMK
Age: 28
here's the manual.
Attached File(s)
Attached File  _Snow_2006_2008_FS_FST.pdf ( 26.35mb ) Number of downloads: 1398
 


--------------------
2007 RMK Dragon 700
Slydog Powder Hounds w/ 8" bergstrom triple points
2012 Timbersled Skid 155" w/ Exit shocks
Holz Spindles
SLP Can
V-Force3 Reeds
Go to the top of the page
 
+Quote Post
 

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 

Lo-Fi Version
Powered By IP.Board © 2013  IPS, Inc.
Licensed to: Polaris Files
Help Search Members Calendar
BottomCorner PageBorder
BlueBar
-